features superior circuit protection overcurrent & overvoltage protection blocks surges up to rated limits high-speed performance small smt package rohs compliant* agency recognition: applications slic protection cable & dsl mdu/mtu modems ont voice/dsl line cards tbu-pl series - tbu high-speed protectors *rohs directive 2002/95/ec jan 27, 2003 including annex. speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. general information the tbu-pl series of bourns ? tbu ? products are low capacitance dual bidirectional high-speed protection components, constructed using mosfet semiconductor technology, and designed to protect against faults caused by short circuits, ac power cross, induction and lightning surges. in addition to overcurrent protection, an added feature is the voltage monitoring on the two lines. if the voltage on the line drops below v ss then the voltage will trigger the device to switch to the blocking state. the tbu ? high-speed protector placed in the system circuit will monitor the current with the mosfet detection circuit triggering to provide an effective barrier behind which sensitive electronics will not be exposed to large voltages or currents during surge events. the tbu ? device is provided in a surface mount dfn package and meets industry standard requirements such as rohs and pb free solder re? ow pro? les. agency approval tbu ? device line 1 slic line 1 line 2 slic line 2 v dd v ss description ul file number: e315805 industry standards (in conjunction with ovp device) absolute maximum ratings (@ t a = 25 c unless otherwise noted) symbol parameter part number value unit v imp peak impulse voltage withstand with duration less than 10 ms tbu-pl050-xxx-wh tbu-pl060-xxx-wh tbu-pl075-xxx-wh tbu-pl085-xxx-wh 500 600 750 850 v v rms continuous a.c. rms voltage tbu-pl050-xxx-wh tbu-pl060-xxx-wh tbu-pl075-xxx-wh tbu-pl085-xxx-wh 300 350 400 425 v t op operating temperature range -55 to +125 c t stg storage temperature range -65 to +150 c t jmax maximum junction temperature +125 c esd hbm esd protection per iec 61000-4-2 on line pads 2 kv electrical characteristics (@ t a = 25 c unless otherwise noted) symbol parameter part number min. typ. max. unit i trigger current required for the device to go from operating state to protected state tbu-plxxx-100-wh tbu-plxxx-200-wh 100 200 150 300 200 400 ma r device series resistance of the tbu ? device 40 50 55 r match package resistance matching of the tbu ? device #1 - tbu ? device #2 0.5 1.0 t block time taken for the device to go into current limiting 1 s i q current through the triggered tbu ? device with 50 vdc circuit voltage 0.25 0.70 1.50 ma i ss operating current with v ss = -50 v 100 a v reset voltage below which the triggered tbu ? device will transition to normal operating state tbu-plxxx-100-wh tbu-plxxx-200-wh 12 15 15 20 22 25 v v to voltage threshold offset with 60 hz applied voltage, with v ss -50 v (v ss - v lineslic ) -1.0 0.2 v v ss operating voltage range relative to v dd -180 -20 v r th(j-l) one side junction to package pads - fr4 using minimum recommended pad layout 110 c/w r th(j-l) both sides junction to package pads - fr4 using minimum recommended pad layout 65 c/w r th(j-l) one side junction to package pads - fr4 using heat sink on board (6 cm 2 ) (0.5 in. 2 ) 40 c/w r th(j-l) both sides junction to package pads - fr4 using heat sink on board (6 cm 2 ) (0.5 in. 2 ) 70 c/w *rohs compliant l501 c954 solutions available for gr-1089-core, itu-t and a combination of both.
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. tbu-pl series - tbu high-speed protectors functional block diagram reference application the tbu-pl series are high-speed protectors used in voice/ voip slic applications.the maximum voltage rating of the tbu ? device should never be exceeded. where necessary, an ovp device should be employed to limit the maximum voltage. a cost-effective protection solution combines bourns ? tbu ? protection devices with a pair of bourns ? movs. for bandwidth sensitive applications, a bourns ? gdt may be substituted for the mov. if en55024 emc compliance is required, the tbu ? device may require capacitors to be ? tted between the tip and ring connections and ground. mov 1 4 2 8 5 6 mov tbu ? device gnd -vbat line 1 slic v dd v ss line 2 slic line 1 line 2 c1 c2 the tbu ? device, constructed using mosfet semiconductor technology, placed in the system circuit will monitor the current with the mosfet detection circuit triggering to provide an effective barrier behind which sensitive electronics are not exposed to large voltages or currents during surge events. the tbu ? device operates in approximately 1 s - once line current exceeds the tbu ? device?s trigger current i trigger . when operated, the tbu ? device r estricts line current to less than 1 ma typically. when operated, the tbu ? device will block all voltages including the surge up to rated limits. when the voltage on the slic output is driven below (v bat ? v to ) the tbu-pl series device switches to the blocking state, regardless of output current in the device. after the surge, the tbu ? device r esets when the voltage across the tbu ? device falls to the v reset level. the tbu ? device will automatically reset on lines which have no dc bias or have dc bias below v reset (such as unpowered signal lines). if the line has a normal dc bias above v reset , the voltage across the tbu ? device may not fall below v reset after the surge. in such cases, special care needs to be taken to ensure that the tbu ? device will reset, with software monitoring as one method used to accomplish this. bourns application engineers can provide further assistance. basic tbu operation line 1 high voltage switch line 1 slic v ss line 2 line 2 slic current sense + voltage comparator high voltage switch current sense + voltage comparator v ss v dd v ss v dd v dd
tbu-pl series - tbu high-speed protectors speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. bourns ? tbu ? device solutions * gdt special test protector with dc breakdown (dcbd) of less than 330 v. notes: 1) the le9500, le9520 and le9530 (ve950 series) require a 200 ma i trigger tbu ? device for normal operation. other slic types should use the 100 ma device. 2) the mov maximum continuous rms voltage rating should not be exceeded. the exception is where the data sheet highlights with stand capability such as the 600 v rms , 1 a for 0.2 s, for example. 3) if en55024 emc compliance is required, the tbu ? device may require capacitors to be ? tted between the tip and ring connections and ground (i.e. in parallel with the mov device). the capacitance value can be chosen to meet levels as follows: 10 nf for en55024 level 1 20 nf for en55024 level 2 47 nf for en55024 level 3 selection of capacitor voltage rating depends upon tbu ? part number selection. recommendations include: tbu-pl050 & tbu-pl060 series: 120 vac, 500 v peak surge rated tbu-pl075 & tbu-pl085 series: 240 vac, 750 v peak surge rated depending upon the slic type, it is usually possible to remove any emi capacitors present between the output of the slic and g round when using capacitors c1 and c2 in parallel with the movs. industry standard surge & ac withstand tbu? device p/n qty. ovp device p/n qty. telcordia gr-1089-core intra-building port type 4 1500 v, 100 a 2/10 s 120 v rms , 25 a, 900 s TBU-PL050-100-WH 1 mov-07d201k 2 telcordia gr-1089-core intra-building port type 4a 1000 v, 100 a 10/1000 s 120 v rms , 25 a, 900 s tbu-pl060-100-wh 1 mov-10d201k 2 non-gr-1089-core intra-building speci? cations 5000 v, 500 a 2/10 s 230 v rms , 25 a, 900 s tbu-pl085-100-wh 1 mov-10d361k 2 1500 v, 100 a 2/10 s 275 v rms , 25 a, 900 s tbu-pl085-100-wh 1 mov-10d431k 2 itu-t basic k.20, k.21, k.45 4000 v, 40 10/700 s 230 v rms 10 - 1000 , 900 s 600 v rms 600 , 0.2 s tbu-pl075-100-wh 1 mov-10d361k 2 4000 v, 40 10/700 s 230 v rms 10 -1000 , 900 s 600 v rms 600 , 0.1 s tbu-pl060-100-wh 1 tisp4400m3bj 2 itu-t enhanced k.20, k.21, k.45 6000 v, 40 10/700 s 240 v rms 10 - 1000 , 900 s 600 v rms 600 , 0.2 s 600 v rms 600 , 1 s* 1500 v rms , 200 , 2 s* tbu-pl085-100-wh 1 mov-10d391k 2 6000 v, 40 10/700 s 240 v rms 10 - 1000 , 900 s 600 v rms 600 , 1 s 1500 v rms , 200 , 2 s tbu-pl060-100-wh 1 tisp4500h3bj 2
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. tbu-pl series - tbu high-speed protectors performance graphs typical v-i characteristics (tbu-pl085-200-wh) tracking voltage characteristics typical trigger current vs. temperature 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -75 -50 -25 0 25 50 75 100 125 junction temperature (?) normalized trigger current typical resistance vs. temperature 2.2 1.6 1.8 2.0 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -75 -50 -25 0 25 50 75 100 125 junction temperature (?) normalized resistance current (50 ma/div) voltage (5 v/div) i trigger v reset power derating curve one side, no pcb cu one side, 0.5 sq. in. pcb cu two sides, no pcb cu two sides, 0.5 sq. in. pcb cu ambient temperature (?) 20 3.0 2.5 2.0 1.5 1.0 0.5 0.0 40 60 80 100 120 140 total max. power (w) 100 90 80 70 60 50 40 -4 -3 -2 -1 0 1 2 3 4 voltage threshold offset (v) resistance ( ) v bat range of -25 v to -150 v typical surge response voltage: 100 v/div time: 250 ns/div current: 100 ma/div (TBU-PL050-100-WH with mov-07d201k using 1800 v 1.2/50 ms surge pulse)
product dimensions pin 1 & backside chamfer 4.00 (.157) 0.00 - 0.05 (.000 - .002) 0.80 - 0.95 (.031 - .037) 6.50 (.256) 0.85 (.033) 0.85 ?0.05 (.033 ?.002) 0.90 (.035) 0.85 (.033) 0.30 (.012) 0.30 (.012) 1.335 (.053) 1.335 (.053) 1.275 (.050) 1.275 (.050) 0.85 (.033) 0.85 (.033) 0.85 (.033) 0.73 (.029) 1.20 (.047) 1.20 (.047) 1.35 (.053) 1.35 (.053) 0.85 (.033) 1.275 (.050) 0.725 (.029) 0.825 (.032) 0.70 (.028) 0.825 (.032) 0.40 (.016) 1.15 (.045) 1.25 (.049) 0.75 (.030) 0.75 (.030) 0.75 (.030) 1.30 (.051) c pin 1 0.25 (.010) 0.40 (.016) 0.70 (.028) dimensions: mm (inches) recommended pad layout 1 2 3 4 8 7 6 5 speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. tbu-pl series - tbu high-speed protectors dark grey areas show added pcb copper area for better thermal resistance. thermal resistance vs additional pcb cu area added cu area (sq. in.) 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 120 100 80 60 40 20 0 thermal resistance (?/w) power in one side of tbu device total power in both sides of tbu device tbu ? high-speed protectors have a 100 % matte-tin termina- tion ? nish. for improved thermal dissipation, the recommended layout uses pcb copper areas which extend beyond the exposed solder pad. the exposed solder pads should be de? ned by a solder mask which matches the pad layout of the tbu ? device in size and spacing. it is recommended that they should be the same dimension as the tbu ? pads but if smaller solder pads are used, they should be centered on the tbu ? package terminal pads and not more than 0.10-0.12 mm (0.004-0.005 in.) smaller in overall width or length. solder pad areas should not be larger than the tbu ? pad sizes to ensure adequate clearance is maintained. the recommended stencil thickness is 0.10-0.12 mm (0.004-0.005 in.) with a stencil opening size 0.025 mm (0.0010 in.) less than the solder pad size. extended copper areas beyond the solder pad signi? cantly improve the junction to ambient thermal resistance, resulting in operation at lower junction temperatures with a corresponding bene? t of reliability. all pads should soldered to the pcb, including pads marked as nc or nu but no electrical connection should be made to these pads. for minimum parasitic capacitance, it is recommended that signal, ground or power signals are not routed beneath any pad.
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. 3312 - 2 mm smd trimming potentiometer tbu-pl series - tbu high-speed protectors re ow pro le pro le feature pb-free assembly average ramp-up rate (tsmax to tp) 3 c/sec. max. preheat - temperature min. (tsmin) - temperature max. (tsmax) - time (tsmin to tsmax) 150 c 200 c 60-180 sec. time maintained above: - temperature (tl) - time (tl) 217 c 60-150 sec. peak/classi? cation temperature (tp) 260 c time within 5 c of actual peak temp. (tp) 20-40 sec. ramp-down rate 6 c/sec. max. time 25 c to peak temperature 8 min. max. how to order tbu - pl 085 - 100 - wh tbu ? product series pl = dual bidirectional series impulse voltage rating 050 = 500 v 060 = 600 v 075 = 750 v 085 = 850 v trigger current 100 = 100 ma 200 = 200 ma hold to trip ratio suf? x w = hold to trip ratio package suf? x h = dfn package typical part marking pin 1 manufacturing date code - 1st digit indicates the year? 6-month period. - 2nd digit indicates the week number in the 6-month period. - 3rd & 4th digits indicate specific lot for the week. 6-month period codes: a = jan-jun 2009 c = jan-jun 2010 e = jan-jun 2011 b = jul-dec 2009 d = jul-dec 2010 f = jul-dec 2011 manufacturer? trademark product code - 1st digit indicates product family: l = tbu-pl series - 2nd & 3rd digits indicate impulse voltage: 50 = 500 v 60 = 600 v 75 = 750 v 85 = 850 v - 4th digit indicates trigger current: 1 = 100 ma 2 = 200 ma 4 1 5 8 6 2 device pin out pad # pin out 1 line 1 2v dd (slic ground or 0 v) 3 not used 4 line 1 slic pad designation pad # pin out 5 line 2 slic 6v ss (slic negative supply or -v bat ) 7 not used 8 line 2
speci cations are subject to change without notice. customers should verify actual device performance in their speci c applications. 3312 - 2 mm smd trimming potentiometer tbu-pl series - tbu high-speed protectors rev. 07/11 ?bu?is a registered trademark of bourns, inc. in the u.s., taiwan and european community. packaging speci cations b a d c n f g (measured at hub) user direction of feed k 0 b 0 p 2 d 1 center lines of cavity embossment t d p 0 top cover tape e w p a 0 dimensions: mm (inches) a b c d g n min. max. min. max. min. max. min. max. ref. ref. 326 (12.835) 330 (13.002) 1.5 (.059) 2.5 (.098) 12.8 (.504) 13.5 (.531) 20.2 (.795) - 16.5 (.650) 102 (4.016) a 0 b 0 d d 1 e f min. max. min. max. min. max. min. max. min. max. min. max. 4.30 (.169) 4.50 (.177) 6.70 (.264) 6.90 (.272) 1.5 (.059) 1.6 (.063) 1.5 (.059) - 1.65 (.065) 1.85 (.073) 7.4 (.291) 7.6 (.299) k 0 p p 0 p 2 t w min. max. min. max. min. max. min. max. min. max. min. max. 1.0 (.039) 1.2 (.047) 7.9 (.311) 8.1 (.319) 3.9 (.159) 4.1 (.161) 1.9 (.075) 2.1 (.083) 0.25 (.010) 0.35 (.014) 15.7 (.618) 16.3 (.642) quantity: 3000 pieces per reel asia-paci c: tel: +886-2 2562-4117 fax: +886-2 2562-4116 europe: tel: +41-41 768 5555 fax: +41-41 768 5510 the americas: tel: +1-951 781-5500 fax: +1-951 781-5700 www.bourns.com
|
